em99sport
12-17-2007, 07:46 PM
The BRP MP62 kit from my '99 is for sale. I'll sell the whole package or simply just the blower and intercooler, but not will not part out the supercharger or intercooler. The whole kit consists of:
BRP MP62 kit for '99-'00 (circa summer '05)
(stock throttle body, 6-rib, 115 crank/67.5mm nose for 1.70 pulley ratio- 8 psi on gauge)
JR Powercard w/ BRP plug-in harness
Track Dog air/air intercooler (sans plastic shields)
RC 270cc injectors
OE '01 exhaust manifold
Track Dog header blanket
Enthuza Speeder stainless axle-back exhaust
http://www.youtube.com/watch?v=ZGXT-_KS9EE
http://www.youtube.com/watch?v=VoeAakp4RSo
The car runs well once warmed up a bit, but the cold start idle isn't good in its current state. I didn't spend much time trying to adjust it, as I found it to be a good way to ensure that I warmed up the car before driving in boost.
The car made 209 rwhp and 173 lb-ft on the Dynojet at DynoLab (Marietta, GA), with only what is listed above.
Again, I will sell just the blower and intercooler to someone who either already has or might not want any of the other stuff, but I figured that I would offer everything together at a better price for someone looking for it all. I will not, however, part out either the blower or intercooler. Anyone interested in anything individually from the RC injectors down can feel free to inquire.
As delivered, this kit will be complete, minus the plastic shrouds for the intercooler, and the gasket between the throttle body and blower. Also, my original instructions didn't make it through two moves since the install, so I cannot provide those.
I installed the kit on my car in the fall of '05, and since then, have driven it less than 7k miles.
If anyone has any questions or concerns, please reply in this thread, or email me at em99sport@gmail.com
BRP MP62 kit for '99-'00 (circa summer '05)
(stock throttle body, 6-rib, 115 crank/67.5mm nose for 1.70 pulley ratio- 8 psi on gauge)
JR Powercard w/ BRP plug-in harness
Track Dog air/air intercooler (sans plastic shields)
RC 270cc injectors
OE '01 exhaust manifold
Track Dog header blanket
Enthuza Speeder stainless axle-back exhaust
http://www.youtube.com/watch?v=ZGXT-_KS9EE
http://www.youtube.com/watch?v=VoeAakp4RSo
The car runs well once warmed up a bit, but the cold start idle isn't good in its current state. I didn't spend much time trying to adjust it, as I found it to be a good way to ensure that I warmed up the car before driving in boost.
The car made 209 rwhp and 173 lb-ft on the Dynojet at DynoLab (Marietta, GA), with only what is listed above.
Again, I will sell just the blower and intercooler to someone who either already has or might not want any of the other stuff, but I figured that I would offer everything together at a better price for someone looking for it all. I will not, however, part out either the blower or intercooler. Anyone interested in anything individually from the RC injectors down can feel free to inquire.
As delivered, this kit will be complete, minus the plastic shrouds for the intercooler, and the gasket between the throttle body and blower. Also, my original instructions didn't make it through two moves since the install, so I cannot provide those.
I installed the kit on my car in the fall of '05, and since then, have driven it less than 7k miles.
If anyone has any questions or concerns, please reply in this thread, or email me at em99sport@gmail.com