Tom @ Fast Forward
11-30-2006, 01:04 PM
When the engine is off and the key is on, the PC-Pro will oscillate the left Green and right Red LEDs.
http://www.FastForwardSuperchargers.com/Install/PC-Pro_Engine_Off.wmv
To add fuel from 0-2800 RPM you will adjust the Green LED.
http://www.FastForwardSuperchargers.com/Install/0-2800_RPM_Adjust.wmv
To add fuel from 2800-5000 RPM push the mode button until the yellow light appears and adjust it.
http://www.FastForwardSuperchargers.com/Install/2800-5000_RPM_Adjust.wmv
To add fuel from 5000-7000 RPM push the mode button until the red light appears and adjust it.
http://www.FastForwardSuperchargers.com/Install/5000-7000_RPM_Adjust.wmv
To move the entire fuel curve up and down push the mode button until the yellow and right side blue lights appears and adjust it. That will keep the flat fuel curve but move it richer or leaner across the board.
http://www.FastForwardSuperchargers.com/Install/Yellow-Blue_Adjust.wmv
Then press the mode button until the red and blue lights are on together and adjust the red to the same point as the previous yellow-blue.
http://www.FastForwardSuperchargers.com/Install/Red-Blue_Adjust.wmv
Normally, you will leave the Green, Yellow and Red settings on zero and simply move the curve up and down with the Yellow-Blue and Red-Blue settings.
For the PC-Pros used for the E-Cool 5th injector, the only adjustment is the Green-Blue. It will add or remove fuel across the board. The Green, Yellow and Red lights still show up but have no function.
When the car is running, the lights will move across the card at basically 1 light per 1000 RPM. You will also note that they change color when they get in the Green, Yellow or Red zones so it is easy to note which color you need to adjust while monitoring A/F. Note, they only function while in boost so revving the engine in neutral will not show any change in lights. The E-Cool version of the PC-Pro shows Boost on the LEDs. It is roughly 2 PSI per light (8 lights=15PSI). For better resolution, there are time when two adjacent lights are on at the same time. If 2 and 3 are on, for example, that is the equivalent of 2.5.
The fuel can be adjusted any time power is on to the card. It doesn't matter if the engine is running or not and changes take effect immediately.
http://www.FastForwardSuperchargers.com/Install/PC-Pro_Engine_Off.wmv
To add fuel from 0-2800 RPM you will adjust the Green LED.
http://www.FastForwardSuperchargers.com/Install/0-2800_RPM_Adjust.wmv
To add fuel from 2800-5000 RPM push the mode button until the yellow light appears and adjust it.
http://www.FastForwardSuperchargers.com/Install/2800-5000_RPM_Adjust.wmv
To add fuel from 5000-7000 RPM push the mode button until the red light appears and adjust it.
http://www.FastForwardSuperchargers.com/Install/5000-7000_RPM_Adjust.wmv
To move the entire fuel curve up and down push the mode button until the yellow and right side blue lights appears and adjust it. That will keep the flat fuel curve but move it richer or leaner across the board.
http://www.FastForwardSuperchargers.com/Install/Yellow-Blue_Adjust.wmv
Then press the mode button until the red and blue lights are on together and adjust the red to the same point as the previous yellow-blue.
http://www.FastForwardSuperchargers.com/Install/Red-Blue_Adjust.wmv
Normally, you will leave the Green, Yellow and Red settings on zero and simply move the curve up and down with the Yellow-Blue and Red-Blue settings.
For the PC-Pros used for the E-Cool 5th injector, the only adjustment is the Green-Blue. It will add or remove fuel across the board. The Green, Yellow and Red lights still show up but have no function.
When the car is running, the lights will move across the card at basically 1 light per 1000 RPM. You will also note that they change color when they get in the Green, Yellow or Red zones so it is easy to note which color you need to adjust while monitoring A/F. Note, they only function while in boost so revving the engine in neutral will not show any change in lights. The E-Cool version of the PC-Pro shows Boost on the LEDs. It is roughly 2 PSI per light (8 lights=15PSI). For better resolution, there are time when two adjacent lights are on at the same time. If 2 and 3 are on, for example, that is the equivalent of 2.5.
The fuel can be adjusted any time power is on to the card. It doesn't matter if the engine is running or not and changes take effect immediately.